How to Test Sump Pump with Radon System

A sump pump is a device that can help keep your properties safe from any type of water damage. Whenever there’s a storm, a water pump will wash out the excess water from the foundation of a property and transport them away. But to ensure the proper functionality of the impulse pump, testing it with a radon system for maintenance is a must.

It only takes a few moments to test a rope pump with a radon system, and it doesn’t demand any special skills as well. Therefore, learning how to test the sump pump with a radon system will be an easy and interesting task for everyone.

Let’s dive into the ways to test an electro pump with a radon system as follows:

How to Test Sump Pump with Radon System?

There are several ways to test a pitcher pump with a radon system, and here we’ll discuss the most popular and simplest one:

1. First, you need to locate the exit pipe. After finding the exit pipe, you’ll notice that it’s draining out water from your sump pump outside your home. Therefore, you need to inspect it as early as possible to make sure the pipe isn’t clogged with debris or dirt. You need to ensure that the pipe is directing water far away from your home’s foundation.

2. Any debris or dirt got inside of the centrifugal pump must be removed right away to make sure that the pump won’t clog in any situation. The pump is generally installed in the crawlspace or basement near the walls of a building’s foundation. Radon mitigation without a sump pump is not an option for any house or foundation.

3. The first and foremost way to test your passive radon system sump pump is by tracing both the electrical cords of your hand pump. The cord plugs of the hydraulic pump race back into the floating cord plug. Therefore, both the cables should automatically be unplugged, for which only the rope pump cord must be plugged into the outlet.

4. If you listen to humming sounds while turning the water pump on, your pump is working fine. It means both the cords must be connected the same way it was before (first the float cord, then the float plug into the pump cord at the back). Sump pump radon mitigation cost is not very high nor affordable, rather, the cost is in between.

5. Since all the electro pumps don’t have two wires on them, the process will also be different from testing single-corded impulse pumps. Here they are:

• Twenty liters of water (approximately) must be poured into the pit of your pitcher pump slowly until there is afloat. When the float rises, your rope pump should kick on. While it has turned on, the water will start pumping out, and therefore the pump should automatically switch itself off when it has washed down all the water. You must repeat this test to make sure that your device is working fine.

• But if pouring that much water into your centrifugal pump is not an option for you, then you need to lift the float somehow, and you should check whether the pump gets turned on or not. However, the hand pump should not go running for more than 20-30 seconds. Otherwise, the motor will get damaged.

Also, read:

• How to increase run time of sump pump
• How Much Power Does A Sump Pump Draw?

How to Install a Sump Pump with Radon Mitigation System

FAQs

Is the radon system connected to the sump pump?

Water pump seals will decrease radon exposure and be effective in a house with normal water levels. But when your house’s radon levels are high, it won’t be enough. Therefore, a sealed positive displacement pump with a professionally handled and installed radon system of mitigation will work hand-in-hand to ensure protection from radon gas.

Does a sump pump need to be sealed for radon?

If the hand pump of your house doesn’t get utilized at a suction stage, then it’ll need to be sealed so that the radon can’t barge into your house through that opening. Even when the hydraulic pump is being used as a point or phase of suction, it’ll still need to be capped.

How do you test a basement sump pump?

If the rope pump you own has only one cord, you need to test your impulse pump by pouring five gallons of water into the basement or pit of your pump. The water will make the float rise, and then the pump will turn on automatically. When the water gets pumped, you need to make sure that your pitcher pump switches itself off.

Wrap Up

That’s all regarding how to test the sump pump with a radon system. An electro pump washes down the water from the final level of a house and pumps it outside of your house. When the radon levels, then you can always add a fan.

Related:

• Hide sump pump discharge pipe
• Hide the sump pump in the basement