How to Hide Sump Pump Discharge Pipe?

A sump pump discharge hose is a technique that allows for the removal of the accumulated water from your property toward linked drainage. Being connected to the pump, it’s commonly engulfed or standing out over the ground to join the disposal area.

But, keeping the discharge pipe open can interrupt the outlook. You can avoid this problem with an underground sump pump drainage line.

In this article, we’ll discuss how to hide sump pump discharge pipe in the right way. 

How to Connect Sump Pump Discharge Hose

Now, we’ll discuss step-by-step connecting the discharge hose to your sump pump below-

Step 1: Attach a 1 1/4- or one 1/2-inch length of PVC pipe with the sum pump’s discharge point. And, now apply PVC cement for gluing before you place the male connector through to the female connector.

Step 2: To set out as a weep hole, drill a hole of ¼” slot in the plastic hose about 6-inches high up the discharge machine to serve as a weep hole.

Step 3: Use a hacksaw to put a vertical check valve overhead the weep hole of the discharge pipe. Maximum check valves assimilate hose clamps and rubber couplings. Fasten the coupling on the hose with a screwdriver.

Step 4: Make a hole in the wall through which the pipe will depart the construction. Dig a ¼” inner hole to help pinpoint the position before drilling outdoors with an approximate 2-inch-sized bit. If it’s a brick wall, inner drilling may lead to side damage. In that case, use a hammering drill to make the hole.

Step 5: Directly expand the discharger line with extra PVC pipe sections and securely join PVC cement till it extends to the outside and makes a hole of several inches throughout the spot.

Step 6: Use silicone caulk to seal the discharge line opening to make a seal. Make sure no air or water can invade the pipe.

Step 7: If the drain pipe is routed below the ground to a drain field or outlet, dig a trench for it. Ensure the channel has a bit downward slope to allow water to flow competently.

Step 8: Attach a PVC booster to the discharge pipe’s end to increase it to more than 3-4” across, based on the scale of the large pipe.

Step 9: To reach out the drainage line toward a chosen outlet, if found necessary, connect the sections of PVC pipes and fittings. And fill up any heretofore uncovered space.

How To Hide Sump Pump Discharge Pipe

The main thing to consider while placing the discharge line is never to put it too near your house. Periodically, your entire backyard or basement outlook can get dampened.

So, the solution is to keep the endpoint of the discharge pipe about 10-20 feet away from the foundation. Besides this, check out if the sewage line is closer to the discharge pipe. Otherwise, there can be a possibility of sewage line flooding. Also read How to hide the sump pump in the finished basement

How To Bury Sump Pump Discharge Pipe

Remember, the underground hose must attach to a suitable disposal point if you have a proper plan for burying the drainage line. 

Step 1

Select the burying location. It would be great if you plan to dispose of the line toward the city-storm water system or sump pump collection point in your area.

Also, check out if there are any underground pipes, power cables, or water lines within your location area. Consult your local public works department about the height of the storm sewer or sump pump collecting system.

Step 2

Build a tunnel along the route you decided. As the trench goes from the discharge point to the home, incline it by 1 inch every 8 feet. In the channel lay a 4-inch PVC pipe. Before bonding the pipe together with PVC adhesive, ensure it fits properly.

Step 3

Attach an elbow to the input end of the underground pipe to connect it to the sump pump. Make sure to attach this elbow to a line length long enough to reach the house’s sill.

Then, install another elbow and a short piece of pipe through the house’s sill. And connect the sump pump system’s lines to a pipe in the home’s basement.

Step 4

Replenish the channel with the soil that was withdrawn during digging. Lay the sod well over the area and soothe the ground to the usual compression.

Related:

• Best sump pump deep cycle battery
• Best battery backup sump pump

FAQs

• Where to run sump pump discharge?

The sump pump discharge is best to draw away from your house. Avoid flowing the drainage onto sidewalks, driveways, or other paved surfaces. Some homeowners want to connect the discharge hose to their sewer line, but it is against the code.

• How do I hide the drain pipe in my sump pump?

Though you can drag the pipe to a suitable drain field or ditch area much far from your house. Also, you can draw it to a considerable length underground.

• How far away from the house should the sump pump discharge?

Generally, your sump pump discharge hose should be 5-10 feet away from the foundation. But, a 20-feet duration from your basement is better. If not, the constant flow will make your soil reabsorbed, causing erosion by damaging the foundation.

• Where do you discharge water from a sump pump?

As pumping discharge water from a sump pump toward the street is illegal, run it away from your place into a drain field or ditch area. Avoid running the water flow through paved surfaces, sidewalks, or driveways. The best is to have external water discharging line that goes sufficiently far from your home’s downward slope.

Final Verdict

Well, that was all regarding how to hide a sump pump discharge pipe. Now you can eliminate unnecessary problems by removing the accumulated water to a suitable place while keeping the discharge line creatively hidden.